General Operation of the Q2 Water Energy System
Q2 (PDF) User Guides
Q2 Conductivity Guidelines
Q2 Recommended Usage Times
Possible Effects While Using the Q2
Preparing the Bath
"Charge" Drinking water
Cleaning the ORB/Array
of the Q2 Water Energy System
The Q Energy Spa System is very simple to use.
Everything that you require is supplied with your "Q Energy Spa System kit".
The Q Energy Spa System ORB has been specifically designed to be used in water.
It is vitally important that you read the booklet
accompanying the System very carefully before operating.
We have mauals for each machine avalable for purchase CLICK HERE
Q2 ENERGY SPA: Models 4100, 4105, 3100, 2500
Q2 FAQ - (Frequently Asked Questions
Troubleshooting Guide for Models #4100, #4105View
ORB Ring & Track Change Guide: View
"Old" ARRAY Ring & Track Change Guide: CLICK HERE
Additional Natural Wellness Information:
Quantum Field Science: CLICK HERE
Detoxification of the Body: CLICK HERE
IMPORTANT NOTICE to all Q2
Energy Spa users:
To test the conductivity of your water if your
unit indicates insufficient conductivity.
The maximum amount of salt or Potassium Citrate you
will need to add is One heaped teaspoon to 200 millilitres or
in US measurements 1/3 of a pint of hot water and add that to
9 litres or 2 gallons of water. This will raise the
conductivity more than enough for the Q2 Energy Spa to
Should your Q2 system still indicate that there is
insufficient conductivity to operate it is not conductivity
but most likely poor connections in the Mohawk that are the
problem. Adding anymore than this amount will only damage the
contacts in the Mohawk connector on the 3100 and 4100 model,
and will degrade your positive ring and track sets far more
quickly than normal. All of which are not covered under
warranty. Should you still experience issues with insufficient
conductivity please contact the nearest offices of Q – The
Experience for detailed assistance.
Recommended usage Times
The usage times with this System are important. It is recommended 35 minutes is spent in the water with this system for each session. This time period is a maximum for all organisms, however some organisms may require less time and this can vary from organism to organism and condition to condition. The recommended usage time is based on one complete cycle of water, which is 17 minutes. To ensure beneficial results, we recommend two cycles of water, hence 35 minutes.
The System should be used every second day (and only every second day) for a period of 1 month. After that, usage of the system is only as often as feels necessary, but never more than every second day.
Possible Effects While Using the Q Energy Spa
Using the Q Energy Spa System for the first few times can cause a number of effects that maybe noticed and observe during and briefly after usage. These effects vary between organisms and may appear at any point during the usage times. The following is a list of sensations that may be experienced.
These effects generally last only a few minutes after usage, however if the body mass should show any signs of distress, the process/session should be terminated immediately and following sessions should not go any longer than that time frame for a period of 14 sessions.
- Tingling sensations in various parts of an organism
- Tingling in scratches, cuts and abrasions.
- A shortness of breath towards the end of usage.
- A slight pain where possibly the organism is unhealthy.
- A tightening sensation in affected areas.
Who should not use the Q Energy Spa System?
There are however a few organisms that cannot use the Q Energy Spa System for various reasons.
- A body mass that has battery operated implants (eg. Pacemakers)
- Any Body mass that has received an organ transplant.
- A pregnant Body Mass.
Remember to leave the power supply a safe distance away from the water.
Preparing the Bath
There are many varieties of tubs to use.
- Copper Tub (available from WebDeb.Com)
- Plastic Tub (Any size to hold water for your feet)
- Bath Tub ahhhh for the whole body ahhhh...
Note: A dishpan sized container will fit most feet plus the array and is still light enough to empty easily. Plastic is my preference (due to weight). Glass and copper are also fine containers.
Does the type of water you use really matter?
Yes and No. I usually use tap water in my bath ... it's the easiest because
there is no need to buy water, lug water or use salt or potassium citrate.
I personally do not notice a difference in potency between tap water and distilled,
but waters vary a lot from one location to another.
I do, however, like to use distilled water and potassium citrate when doing a
demonstration. Since the distilled water has no mineral content .. and potassium
citrate is very simple, little or no discoloration occurs. I really don't want to
make a fuss over the colors or stuff in the water. It's mostly interactions of the water content and the fields. Instead, focus on what is happening inside your body or the body of your client. It's subtle. If you feel nothing ... relax deeper and see if you can sense the subtle flows of energy. Focus within. Breathe. Relax. Let go of all stress. Let go of all holding on. If something remarkable happens in the water, be amazed. Don't try to explain it. There is a lot happening in the water even if you don't notice anything! And a lot more is happening in your body.
Cleaning Your Q2
Following each Q session, rinse your array under running water.
I like to clean the Q in the following cleaning solution below,
about every 3rd use. Cleaning it often can extend the life of the array.
CLR (can be bought at any drugstore) Mix 50% CLR and 50% water.
If stored in lidded plastic containers your cleaning mixture may
be reused for months.
100% Organic, citrus based, environmentally friendly, non-hazardous, biodegradable solution, when mixed with water.
It is also septic and grey water safe.
In a sealable container big enought to fit and orb or array, place the 40g sachet and fill with water (about 1.5 liters).
Be sure to add enough water to cover the entire orb/array and stir mixture til powder is dissolved.
Soak the orb/array for 5-10 minutes after every session; to ensure maximum efficiency.
Charging Drinking Water
Using drinking water charged in the Q2 is highly beneficial and is easily done
by placing filled glass bottles in a basin of water with the orb, switching on
the unit and running it for the period of a session.
Only 8 ounces per day should be consumed and it is important to drink it within
a short space of time, not spread it over the day, since the charge it supplies
to the body should be allowed to subside before the next amount is taken.
The water will hold the charge for a maximum of 90 hours.